A572 steel plate has good structural quality with an optimal combination of high strength, high notch toughness, good weldability, and high value. Due to its alloying elements, it can be a little more difficult to form and pre-testing of both welding and post-welding heat treatments is recommended. A588 / A606 / A242 Structural, Carbon & HSLA Steel Plate 25 rows · Grade Gauge (Inches) Width (Inches) Length (Inches) A588:0.1875:96:240/480:A588:
A588 is a high strength, low alloy steel plate that was developed for use cases demanding higher strength and a longer life cycle. A588 is known for its atmospheric corrosion resistance thanks to a natural patina of rust that forms when exposed to outdoor weather conditions. ARE YOU P SPECIFYING M - AISCfying ASTM A588 grade 42, 46, or 50. However, the availability and cost effec-Modern Steel Construction / February 1999 tiveness of structural plates in grades other than ASTM A36 should be con-firmed prior to their specification. Note also that the availability of grades other than ASTM A36 varies through the range of thickness. Regardless of the material specifica-tion chosen, the production tolerances for structural plates are given in ASTM ASTM A588 Grade A|A588 Gr.A STEEL PLATE__Steel Supplierastm a588 grade a|a588 gr.a steel plate A588 Grade A steel plate is for high strength low alloy structural steel with 345Mpa minimum yield point to 100mm thickness. When propertly exposed to the atmosphere, A588 Grade A is suitable for many applications in the bare condition.
ASTM A588 has a 50ksi minimum yield strength and a 70ksi minimum tensile strength. ASTM A242 This specification is normally applicable to steel plates through one-half inch in thickness. Carbon Steel Plates, ASTM A516-70, A514, A588, HSLA Carbon Steel Plates, CS Plate, IS 2062 Hot Rolled Steel Plates Suppliers, Carbon Steel IS 2002 Chequered Plates Exporters, ASTM A516-70 Carbon Steel Plate, Carbon Steel ASME SA515 Boilers & Pressure Vessel Plates, ASMT A36 Carbon Structural Steel Plates, ASME SA572 High-Strength Steel Plates, A514 High Yield Steel Plates, AISI 1045 Carbon Steel Diamond Plates, ASTM A588 HSLA Steel Plate. Keeping tabs on current ASTM specifications ARE YOU ing ASTM A572 Grade 55, 60 or 65, ASTM A529 Grade 55, ASTM A514 Grade 90 or 100 or ASTM A852. Structural plates with atmospheric corrosion resistance (weath-ering characteristics) can be obtained by specifying ASTM A588 Grade 42, 46 or 50. These and other material specifications applicable to structural plates are shown in Table 2. Structural Bars
ArcelorMittal USA Plate facilities produce seven grades of steel in the ASTM A514 (structural applications) and ASTM A517 (pressure vessel applications) families. These are grades A, B, E, F, H, P and Q. They are chemically identical between A514 and A517 and also similar to the four T-1 grades as follows:Typical Applications Steel Standards - ASTM InternationalASTM's steel standards are instrumental in classifying, evaluating, and specifying the material, chemical, mechanical, and metallurgical properties of the different types of steels, which are primarily used in the production of mechanical components, industrial parts, and construction elements, as well as other accessories related to them. Steel grades according to American standards - A36, Chemical composition A36 - 04b A36 0.26 0.05 0.04 0.40 A572 - 04 Grade 42 0.21 1.35 0.05 0.04 0.40 Grade 50 0.23 1.35 0.05 0.04 0.40
A572 Gr.50 steel plate is typically used whenever a cost savings from a weight reduction can be gained. Bebon will supply ASTM A572-Gr50 plates up to 150mm thickness. A588 Gr.A steel, similar to ASTM A572-Gr50, is also a high strength low alloy steel, but is a Copper Bearing steel offering approximately four times the corrosion resistance of structural carbon steel grade.